120 lines
3.3 KiB
C++
120 lines
3.3 KiB
C++
|
/*
|
||
|
* i2c_port_address_scanner
|
||
|
* Scans ports D0 to D7 on an ESP8266 and searches for I2C device. based on the original code
|
||
|
* available on Arduino.cc and later improved by user Krodal and Nick Gammon (www.gammon.com.au/forum/?id=10896)
|
||
|
* D8 throws exceptions thus it has been left out
|
||
|
*
|
||
|
*/
|
||
|
#include <Arduino.h>
|
||
|
#include <Wire.h>
|
||
|
|
||
|
#include "ota.h"
|
||
|
#include "configuration.h"
|
||
|
#include "helper_3dmath.h"
|
||
|
#include "udpclient.h"
|
||
|
#include "credentials.h"
|
||
|
|
||
|
DeviceConfig config;
|
||
|
|
||
|
uint8_t portArray[] = {16, 5, 4, 0, 2, 14, 12, 13};
|
||
|
//String portMap[] = {"D0", "D1", "D2", "D3", "D4", "D5", "D6", "D7"}; //for Wemos
|
||
|
String portMap[] = {"GPIO16", "GPIO5", "GPIO4", "GPIO0", "GPIO2", "GPIO14", "GPIO12", "GPIO13"};
|
||
|
|
||
|
|
||
|
void check_if_exist_I2C() {
|
||
|
byte error, address;
|
||
|
int nDevices;
|
||
|
nDevices = 0;
|
||
|
for (address = 1; address < 127; address++ ) {
|
||
|
// The i2c_scanner uses the return value of
|
||
|
// the Write.endTransmisstion to see if
|
||
|
// a device did acknowledge to the address.
|
||
|
Wire.beginTransmission(address);
|
||
|
error = Wire.endTransmission();
|
||
|
|
||
|
if (error == 0){
|
||
|
Serial.print("I2C device found at address 0x");
|
||
|
if (address < 16)
|
||
|
Serial.print("0");
|
||
|
Serial.print(address, HEX);
|
||
|
Serial.println(" !");
|
||
|
|
||
|
nDevices++;
|
||
|
} else if (error == 4) {
|
||
|
Serial.print("Unknow error at address 0x");
|
||
|
if (address < 16)
|
||
|
Serial.print("0");
|
||
|
Serial.println(address, HEX);
|
||
|
}
|
||
|
} //for loop
|
||
|
if (nDevices == 0)
|
||
|
Serial.println("No I2C devices found");
|
||
|
else
|
||
|
Serial.println("Scan finished\n");
|
||
|
}
|
||
|
|
||
|
void scanPorts() {
|
||
|
for (uint8_t i = 0; i < sizeof(portArray); i++) {
|
||
|
for (uint8_t j = 0; j < sizeof(portArray); j++) {
|
||
|
if (i != j){
|
||
|
Serial.print("Scanning (SDA : SCL) - " + portMap[i] + " : " + portMap[j] + " - ");
|
||
|
Wire.begin(portArray[i], portArray[j]);
|
||
|
check_if_exist_I2C();
|
||
|
}
|
||
|
}
|
||
|
}
|
||
|
}
|
||
|
|
||
|
void I2C_recovery() {
|
||
|
Serial.println("Starting I2C bus recovery");
|
||
|
delay(2000);
|
||
|
int SDAPIN = 70;
|
||
|
int CLKPIN = 71;
|
||
|
//try i2c bus recovery at 100kHz = 5uS high, 5uS low
|
||
|
pinMode(SDAPIN, OUTPUT);//keeping SDA high during recovery
|
||
|
digitalWrite(SDAPIN, HIGH);
|
||
|
pinMode(CLKPIN, OUTPUT);
|
||
|
for (int i = 0; i < 10; i++) { //9nth cycle acts as NACK
|
||
|
digitalWrite(CLKPIN, HIGH);
|
||
|
delayMicroseconds(5);
|
||
|
digitalWrite(CLKPIN, LOW);
|
||
|
delayMicroseconds(5);
|
||
|
}
|
||
|
|
||
|
//a STOP signal (SDA from low to high while CLK is high)
|
||
|
digitalWrite(SDAPIN, LOW);
|
||
|
delayMicroseconds(5);
|
||
|
digitalWrite(CLKPIN, HIGH);
|
||
|
delayMicroseconds(2);
|
||
|
digitalWrite(SDAPIN, HIGH);
|
||
|
delayMicroseconds(2);
|
||
|
//bus status is now : FREE
|
||
|
|
||
|
Serial.println("bus recovery done, starting scan in 2 secs");
|
||
|
//return to power up mode
|
||
|
pinMode(SDAPIN, INPUT);
|
||
|
pinMode(CLKPIN, INPUT);
|
||
|
delay(2000);
|
||
|
//pins + begin advised in https://github.com/esp8266/Arduino/issues/452
|
||
|
//Wire1.pins(SDAPIN, CLKPIN); //this changes default values for sda and clock as well
|
||
|
Wire.begin();
|
||
|
//only pins: no signal on clk and sda
|
||
|
//only begin: no signal on clk, no signal on sda
|
||
|
}
|
||
|
|
||
|
void loop() {
|
||
|
otaUpdate();
|
||
|
}
|
||
|
|
||
|
void setup() {
|
||
|
Serial.begin(115200);
|
||
|
while (!Serial); // Leonardo: wait for serial monitor
|
||
|
Serial.println("\n\nI2C Scanner to scan for devices on each port pair D0 to D7");
|
||
|
scanPorts();
|
||
|
I2C_recovery();
|
||
|
scanPorts();
|
||
|
|
||
|
setUpWiFi(&config);
|
||
|
otaSetup(otaPassword);
|
||
|
}
|